Follow our Iran coverage

The you are using (Magnetic Lock or Electric Strike)?

Enter programming mode, then press 0 + [New 6-digit Code] + # + [Repeat New Code] + # . 4. User Management Adding Users (Card or PIN) Enter Programming Mode. Press 1 . For Card: Swipe the RFID card.

If you are looking for specific troubleshooting, I can help you with: for magnetic vs. electric strike locks.

The V2000-C is a 125KHz RFID standalone access control keypad supporting up to 1,000 users with 4-digit PINs or EM cards. Featuring a Wiegand 26 interface and a 3-8 cm reading range, the weatherproof unit operates on 12VDC and includes relay outputs for locks and alarms. For detailed programming instructions and wiring diagrams, see the uAmper Manual .

The V2000-C is a single-door multifunction standalone access controller. It supports up to and allows access via RFID card, a 4-to-6 digit PIN, or a combination of both. Operating Voltage: DC 12V ± 10% User Capacity: 2,500 Card Reading Distance: 3–6 cm Active Current: Lock Output Load: Max 3A Operating Temperature: -45°C ~ 60°C 2. Installation and Wiring

This public link is valid for 7 days and shares a thread, including any personal information you added. This link or copies made by others cannot be deleted. If you share with third parties, their policies apply. Can’t copy the link right now. Try again later.

Connect the positive wire of the lock to NC , the negative wire of the lock to GND , and bridge COM to +12V . When power is lost, the lock opens.

Enter Programming Mode -> Press 2 + [Read Card] + # .

| Feature | Specification | | :--- | :--- | | | 125kHz (EM) or 13.56MHz (Mifare) | | User Capacity | 1,000 – 10,000 users (varies by firmware) | | Output Relay | Dry contact (NO/NC/COM), 2A/30VDC | | Power Input | 12V DC ±10%, 1-2A | | Operating Temp | -20°C to +60°C | | Waterproof Rating | IP65 (outdoor keypad models) |

Before installation, ensure your environment meets the following requirements: DC 12V ±10% User Capacity: 1,000 to 2,500 users (model dependent) Card Reading Distance: 3–6 cm Card Type: ID (EM) card or IC (Mifare) card Output Interface: Wiegand 26 (for external readers) Lock Output Load: Max 3A 2. Installation and Wiring

V2000-c Rfid Access Control User Manual

The you are using (Magnetic Lock or Electric Strike)?

Enter programming mode, then press 0 + [New 6-digit Code] + # + [Repeat New Code] + # . 4. User Management Adding Users (Card or PIN) Enter Programming Mode. Press 1 . For Card: Swipe the RFID card.

If you are looking for specific troubleshooting, I can help you with: for magnetic vs. electric strike locks. V2000-c Rfid Access Control User Manual

The V2000-C is a 125KHz RFID standalone access control keypad supporting up to 1,000 users with 4-digit PINs or EM cards. Featuring a Wiegand 26 interface and a 3-8 cm reading range, the weatherproof unit operates on 12VDC and includes relay outputs for locks and alarms. For detailed programming instructions and wiring diagrams, see the uAmper Manual .

The V2000-C is a single-door multifunction standalone access controller. It supports up to and allows access via RFID card, a 4-to-6 digit PIN, or a combination of both. Operating Voltage: DC 12V ± 10% User Capacity: 2,500 Card Reading Distance: 3–6 cm Active Current: Lock Output Load: Max 3A Operating Temperature: -45°C ~ 60°C 2. Installation and Wiring The you are using (Magnetic Lock or Electric Strike)

This public link is valid for 7 days and shares a thread, including any personal information you added. This link or copies made by others cannot be deleted. If you share with third parties, their policies apply. Can’t copy the link right now. Try again later.

Connect the positive wire of the lock to NC , the negative wire of the lock to GND , and bridge COM to +12V . When power is lost, the lock opens. User Management Adding Users (Card or PIN) Enter

Enter Programming Mode -> Press 2 + [Read Card] + # .

| Feature | Specification | | :--- | :--- | | | 125kHz (EM) or 13.56MHz (Mifare) | | User Capacity | 1,000 – 10,000 users (varies by firmware) | | Output Relay | Dry contact (NO/NC/COM), 2A/30VDC | | Power Input | 12V DC ±10%, 1-2A | | Operating Temp | -20°C to +60°C | | Waterproof Rating | IP65 (outdoor keypad models) |

Before installation, ensure your environment meets the following requirements: DC 12V ±10% User Capacity: 1,000 to 2,500 users (model dependent) Card Reading Distance: 3–6 cm Card Type: ID (EM) card or IC (Mifare) card Output Interface: Wiegand 26 (for external readers) Lock Output Load: Max 3A 2. Installation and Wiring